登录    注册    忘记密码

详细信息

Plastic deformation mechanism of negative rake angle tools in low-speed cutting  ( EI收录)  

文献类型:期刊文献

英文题名:Plastic deformation mechanism of negative rake angle tools in low-speed cutting

作者:Hu, Bo Guo, Yong Fen Jiang, Hong Wan Yuan, Sen

第一作者:胡波

通信作者:Hu, B[1];Yuan, S[1]

机构:[1]Guizhou Inst Technol, Sch Mech Engn, Guiyang 550025, Peoples R China

第一机构:贵州理工学院机械工程学院

通信机构:corresponding author), Guizhou Inst Technol, Sch Mech Engn, Guiyang 550025, Peoples R China.|贵州理工学院机械工程学院;贵州理工学院;

年份:2026

卷号:32

外文期刊名:RESULTS IN ENGINEERING

收录:EI(收录号:20263821522651);Scopus(收录号:2-s2.0-105051089869);WOS:【ESCI(收录号:WOS:001884725300001)】;

基金:The authors would like to deeply appreciate the support from Guizhou Provincial Technology Innovation Center-Research on Key Technologies of Advanced Machine Tools(Grant No. JSZX[2025]009); National Natural Science Foundation of China (Grant No. 52265055); The Guizhou Provincial Department of Education 2025 "Hundreds of Schools and Thousands of Enterprises Science and Technology Tackling Unveiled" Program(Grant No. QJJ[2025]003);Guizhou Provincial Youth Science and Technology Talents Growth Project(Grant No. QJJ [2024]163).

语种:英文

外文关键词:Negative rake angle; Plastic deformation; Adiabatic shear; Extrusion-shear composite deformation

摘要:Negative rake angle cutting can significantly enhance tool impact resistance and machining stability; however, the complexity of its plastic deformation mechanism hinders the optimization of tool geometry and cutting parameters. In this study, Ti6Al4V titanium alloy was selected as the workpiece material, and a finite element simulation approach was adopted to systematically investigate the influences of cutting speed (5-20 m/min), feed rate (0.1-0.4 mm/r), rake angle (-15 degrees to 0 degrees), and tool nose radius (0.01-0.04 mm) on the plastic deformation behavior. The evolution of temperature, strain rate, stress, and strain during the elastic, plastic, and fracture states was examined, and the shear band width, degree of chip serration, and damage distribution characteristics were analyzed. The results indicate that there exists a critical transition point of cutting speed at 15 m/min: below this value, strain-rate hardening predominates; above it, thermal softening intensifies and triggers adiabatic shear instability. Increasing the feed rate promotes a transition from localized shear to more uniform flow deformation, yet the cutting force rises linearly, while the damage evolution is stage-dependent and non-monotonic. A more negative rake angle and a larger tool nose radius enhance the extrusion effect, whereas the shearing effect becomes dominant under the opposite conditions. Accordingly, an extrusion-shear composite deformation factor xi was proposed to quantitatively characterize the deformation mode (xi < 1: extrusion-dominated; xi > 1: shear-dominated; xi approximate to 1: optimal range). Furthermore, a critical cutting-speed formula for adiabatic shear instability was established and validated experimentally. The findings provide a theoretical basis for matching process parameters and optimizing tool geometry in negative-rake-angle cutting of difficult-to-machine materials.

参考文献:

正在载入数据...

版权所有©贵州理工学院 重庆维普资讯有限公司 渝B2-20050021-8 
渝公网安备 50019002500408号 违法和不良信息举报中心