文献类型：期刊文献

中文题名：三乙胺对酚醛树脂耐热性及层压制动材料摩擦性能的影响

英文题名：Influence of Triethylamine on Thermal Resistance of Phenolic Resin and Friction Behavior of Laminated Composites

作者：刘渊 罗军 冯晓琴

第一作者：刘渊

机构：[1]贵阳学院材料磨损与腐蚀防护贵州省教育厅特色重点工程中心;[2]贵州理工学院化学工程学院

第一机构：贵阳学院材料磨损与腐蚀防护贵州省教育厅特色重点工程中心,贵州贵阳550005

年份：2014

卷号：42

期号：5

起止页码：75-78

中文期刊名：塑料科技

外文期刊名：Plastics Science and Technology

收录：CSTPCD;;北大核心:【北大核心2011】；

基金：贵州省科技厅工业攻关项目(黔科合GY字[2012]3038);贵州省教育厅产学研基地项目;贵阳市科技局科技特派员项目(筑科合同[2012207]12);贵阳学院校级产学研基地培育项目(201301)

语种：中文

中文关键词：酚醛树脂;三乙胺;固化;胶黏剂;摩擦系数

外文关键词：Phenolic resin; Triethylamine; Curing; Adhesive; Friction coefficient

摘要：以三乙胺作为催化剂制备了热固性酚醛树脂预聚体,并以酚醛树脂预聚体、芳纶纤维、玻璃纤维、铜丝制备了层压式制动材料。利用DSC、TG和蔡氏摩擦试验机等分析手段,对酚醛树脂预聚体的固化行为、固化物的热稳定性及酚醛基层压式制动材料的摩擦性能进行了研究。DSC测试结果表明,用三乙胺催化合成的酚醛树脂预聚体在280℃左右出现一个固化放热峰。TG测试结果表明,用三乙胺催化制备酚醛树脂预聚体存在一个最佳用量,当三乙胺用量为27 g时,酚醛树脂固化物的热性能最好;当三乙胺用量为33 g时,酚醛树脂固化物的初始失重率较大,但在300~400℃时酚醛树脂固化物的热失重率很小。摩擦试验表明,当三乙胺用量为33 g时,层压制动材料的摩擦系数较为稳定。
To investigate the influence of the amount of catalyst on thermal stability of phenolic resin and laminated composite materials, triethylamine was employed to catalyze the polymerization of phenol and formaldehyde. Moreover, laminated composite material was obtained by hot press molding of phenolic resin and aramid fiber, and copper fiber. DSC, TG, and CHASE friction test machine were employed to investigate specific effects of the catalyst on phenolic resin. The results of DSC test show that during the curing process, the phenolic prepolymer shows one exothermic peak which is caused by corsslinking reaction of the phenolic prepolymers at 280~C, and the result of TG test shows that when the amount of triethylamine is 27 g, the thermal stability of phenolic resin is the best; when the amount of the triehtylamine is 33 g, the initial mass loss rate is apparently, however the stability of the phenolic resin is very excellent at 300~400~C, it has almost no mass loss. The CHASE friction test shows that the friction coefficient is relatively stable when the amount of triethylamin is 33 g.